squish

英 [skwɪʃ]

美 [skwɪʃ]

v.  (被)压坏，挤坏; 发吧唧声; 发吱嘎声

过去分词：squished　过去式：squished　现在分词：squishing　第三人称单数：squishes　

BNC.48495 / COCA.19433

牛津词典

verb

• （被）压坏，挤坏
  if sth soft squishes or is squished , it is crushed out of shape when it is pressed
• 发吧唧声；发吱嘎声
  to make a soft wet sucking sound

英英释义

noun

• the noise of soft mud being walked on

verb

• put (a liquid) into a container or another place by means of a squirting action
• walk through mud or mire
  1. We had to splosh across the wet meadow
  Synonym:squelchsplashsploshsloshslop

双语例句

• Reversed squish is mainly concentrated at edge of combustion chamber bowl.
  反喷或逆挤流主要集中在燃烧室边缘上。
• The air motion and squish effect inside the cylinder of a diesel with a cylindrical bowl has been computed, and the results have been analysed in this paper.
  本文对圆柱形燃烧室缸内空气流动、挤流作用进行了模拟，并对计算结果进行了分析。
• The squish patterns in engine piston bowls with different geometry are visualized by the method of oil streak in a motored single cylinder test engine.
  本文在一个拖动的单缸实验机上，利用油点条痕法显示了活塞上燃烧室凹坑中挤流运动的流谱，研究了燃烧室形状和几何尺寸对挤流谱的影响。
• The reflected spray distributes at squish zone and concave zone of combustion chamber, big swirl of spray is obtained and expand to more domains.
  反射后的油束分布在燃烧室的挤流区和凹坑区，形成大的油束涡流，并向较大范围扩展。
• During the compression stroke the turbulence kinetic energy decreases due to the dissipation effect, while the turbulence kinetic energy in the center of the cylinder increases as a result of the squish effect.
  缸内平均湍动能强度在进气冲程中总体呈先增大后减小的趋势，压缩冲程中耗散作用使湍动能降低，但挤流作用使气缸中部的湍动能升高；
• It'll help squish out all that water I've been retaining.
  它能帮我把我一直保持的水份全都挤出来。
• Gas Skunk: This is not good. It's gonna fall and squish us.
  这不好。它就要倒下并压扁我们了。
• And, then we squish all of them up, and that's how we get the contour plot OK, so each of these lines, imagine that this is like some mountain or something that you are hiking on.
  然后把所有等高线聚合到一起，这样就得到了等高线图，对于每一条这些线，想象，你是在爬山或是徒步旅行。
• Valves are clustered near the center of the bore to minimize combustion chamber volume and to provide ample squish area.
  阀门是聚集在附近的孔中心，以尽量减少燃烧室量，以及提供足够的果酱领域。
• By comparison, straight wall chamber ( type A) is easy to be manufactured, has the lowest thermal stress and has obvious squish. Type A is the best combustion room choice.
  比较而言，直壁ω型燃烧室最易制造，热应力较小，挤流作用明显，为最佳燃烧室方案。