scuffing

英 [ˈskʌfɪŋ]

美 [ˈskʌfɪŋ]

v.  磨损; 磨坏; 拖着脚走
scuff的现在分词

现在分词：scuffing　

柯林斯词典

• V-ERG (使)磨损;(使)磨坏
  If youscuffsomething or if itscuffs, you mark the surface by scraping it against other things or by scraping other things against it.
  1. Constant wheelchair use will scuff almost any floor surface...
     任何地板上经常有轮椅走动几乎都会有所磨损。
  2. Molded plastic is almost indestructible, but scuffs easily.
     注塑几乎弄不坏，但是容易磨损。
• VERB 拖着脚走
  If youscuffyour feet, you pull them along the ground as you walk.
  1. Polly, bewildered and embarrassed, dropped her head and scuffed her feet.
     波莉既困惑又尴尬，低下头拖着脚走开了。

双语例句

• The working condition and the form of scuffing failure of valve-valve seat pair are introduced. The method of valve-valve seat tribology designing is provided.
  介绍了气门-气门座摩擦副的工作状况和失效形式，提出了气门-气门座摩擦学设计的方法；
• The temperature effect of scuffing in sliding contact of steel is explored from the point of view of frictional temperature.
  作者从摩擦温度的观点考察了钢在滑动接触中擦伤的温度效应。擦伤试验是在环-块试验机上进行的。
• The research method adopted in the paper are fo some significance to the study of gear scuffing mechanism and the study to increase the gear scuffing load carry capacity.
  本文的研究方法对齿轮胶合机理和提高齿轮胶合承载能力的研究都是有意义的。
• Standard test method for scuffing load capacity of gears
  GB/T13672-1992齿轮胶合承载能力试验方法
• The anti scuffing, friction reducing and wear resistant properties were investigated systematically on a pin on disc tester under engine oil lubrication condition.
  用销盘试验机在机械油润滑条件下对渗硫表面的抗擦伤性能，减摩及耐磨性能进行了系统研究。
• Tess twisted her feet to make a scuffing noise.
  苔丝缠绕着她的两只脚发出摩擦的声音。
• Study on calculating and test method for gear scuffing
  齿轮胶合的计算和试验研究
• Hot load and mechanical load coupling make piston to produce crackle, piston-ring glued and scuffing of cylinder bore and so on.
  热负荷和机械负荷耦合将导致活塞产生裂纹、活塞环胶结以及拉缸等。
• The scuffing resistances of three phosphate coatings of manganese are evaluated in a MQ-800 four ball tester equipped with a new wear sample holder.
  在MQ&800四球试验机上装配了一种新的磨损试验夹具，评价了三种磷酸锰盐涂层的抗擦伤性能；
• The mould test demonstrates that the surface scuffing and metal transferring can be greatly deduced at dry friction condition.
  模具试验表明，复合镀层有效地降低了干摩擦状态下注塑模推管与摩擦件的表面划伤与金属转移。